1200W 185mm mini speed corded plunge-cut electric motor for circular saw


Quick Details

Place of Origin:

Zhejiang, China

Brand Name:


Model Number:



Wood Saw






50/60 Hz

Rated Voltage:


Max. Cutting Depth:


Rated Input Power:

1200W, 1200W

No-Load Speed:


Max. Cutting Width:


Blade Diameter:


Power Source:


Saw Type:

Circular Saw

Product name:

1200W 185mm mini speed corded plunge-cut circular saw blade

No load speed:

5000 r/min








Color box

Packing Size:






Supply Ability

Supply Ability:
60000 Piece/Pieces per Month

Packaging & Delivery

Packaging Details

G.W./N.W.:21/20kg”>Packed in color box or nylon bag


Lead Time
Quantity(Pieces) 1 – 500 >500
Est. Time(days) 45 To be negotiated

Online Customization

1200W 185mm mini speed corded plunge-cut electric motor for circular saw

Product Description

Product Specifications





Rated Input Power


No load speed

5000 r/min

Disc diameter






Features of plunge-cut circular saw:

1.Multiple bevel angle settings for joint cuts

2.Sizeable 185mm blade with 65mm maximum cutting depth

3.Suitable for use on a wide range of materials

4.Dust extraction facility for maintaining a clean work area

A. button

H. knob

B. switch

I. lever

C. plastic nut

J. dust extraction hole

D. hexagonal nut

K. locking flange

E. knob

L. wrench

F. knob

M. 2-pin wrench

G. parallel guide

N. lower blade guard

Operation of plunge-cut circular saw

Adjusting the depth of cut

Caution: Always ensure that the plunge-cut circular saw is switched off and unplugged from the power supply before making any adjustments.

1.Unscrewing plastic nut (C) by turning it anticlockwise.

2.Lift the body of the saw until the blade is at the right depth.

3 Screwing plastic nut(C) by turning clockwise.

Note: Always use the correct blade depth setting. The correct blade depth setting for all cuts should not be more than 6.35mm (1/4”) below the material being cut. Allowing more depth will increase the chance of kickback and result in a rough cut.

Adjusting the bevel angle

Loosen knob E&F and tilt the body of the saw until the required angle is reached. Tighten knob E&F.

Note: Always make a trial cut in a scrap piece of material along a guideline to check the position of the blade relative to the guideline and the angle of cut.

Switching on and off

Connect the plug to the power supply. Press button (A) and squeeze switch (B).

Note: When you release the trigger, the motor turns off and button (A) re-engages to prevent accidental operation.

Caution: Allow the blade to come to a complete standstill before setting the saw down.

Making a cut

Mark the line of cut on the workpiece. Start the motor and let the blade reach full speed (approximately 2 seconds.).Slowly push the saw forward using both hands.

Note: When making a cut always use steady, evenpressure. Forcing the electric circular saw causes rough cuts and could shorten the life of the saw or cause kickback. Allow the blade and the saw to do the work. After completing your cut, release the switch (B) and allow the blade to come to a complete stop. Do not remove the saw from the workpiece while the blade is moving. Since blade thickness varies, always make a trial cut in scrap material along the guideline and adjust the position of the blade guide as necessary

Changing the blade

Caution: Always ensure that the plunge-cut circular saw is switched off and unplugged from the power supply before making any adjustments.

Place saw on its side on a flat surface and set for a minimum depth cut.

Place the 2-pin wrench (M) in the slots of the locking flange (K).

Firmly keep the 2-pin wrench in place while you unscrew the hexagonal nut (D) by wrench(L).

Remove the outer blade flange(K) and the blade bolt(D).

Raise the lower blade guard (N) using lever (I).

Remove the saw blade.

Notes: Clean the saw blade flanges thoroughly before mounting the new saw blade. Wipe a drop of oil onto the inner and outer flange where they will touch the blade. Mount the new saw blade onto the spindle. Replace the outer flange(K) and tighten the blade bolt(D).

After replacing the saw blade, make sure that the saw blade runs freely by turning the blade by hand. Plug the machine into a power socket and run the saw under no load to check that it runs smoothly before using it to cut any material.

Using the parallel guide

The parallel guide (G) allows you to make parallel cuts in a sheet of wood, all at the same width.

Loosen knob (H). Slide the parallel guide (G) through the slots in the base plate. Adjust the parallel fence to the required width and secure it in position with knob (G).

Note: Ensure that the parallel fence rests against the wood along its entire length to give a consistent parallel cut.

Opening the blade protection

The blade protection (N) evolves automatically being pushed by the wood that you cut. To open it

manually, move the lever (I).

Dust extraction

Theplunge-cut circular saw is equipped with a dust extraction hole (J).

Packaging & Shipping

Company Information

  • Specializing in manufacturing and exporting power tools for more than 8 years
  • Export to more than 15countries in Europe, NA the Middle East, Southeast Asia, Africa, South America and areas etc.
  • Replying the e-mail with 24 hours
  • All products destined abroad are in compliance CE, CB, GS, SAA, EMC, ETL and comply to PAH, RoHS and REACH
  • Stable production, consistent quality and fair price

Quality Control

  • Each “component fabrication workshop” is responsible to perform their own QC audits to internal AQL standards or OEM client specifications.
  • Each “assembly workshop” carries out their own IQC and OQC regardless of whether they’re utilizing internally produced or externally purchased components.
  • During assembly, there are further inspections on sub-assemblies at regular “critical to performance” intervals.



Q: What’s your MOQ?

A: Normally our MOQ is 500 units per model, but we can also accept 100-300pcs, it depends on the model.

Q: What’s your payment terms?

A: We could accept L/C sight, T/T ,Paypal and E-credit etc.

Q: What’s the delivery time?

A: Normally our lead time is 45days, but if the quantity is large, or it’s related to some special components, the lead time would be longer.

Q: Can I get free samples?

A: Yes. You pay the sample cost and shipping cost first. We will return you the money back when place official orders.

Our service:

a.1 year warranty

b.1%-2% Spare Parts

c. OEM & ODM are welcome

d. trial orders are available

e. 24 hours online service.

Recent Posts

worm drive

As one of leading worm drive  manufacturers, suppliers and exporters of mechanical products, We offer worm drive gearbox and many other products.

Please contact us for details.

Mail: sales@worm-drive.top

Manufacturer supplier exporter of worm drive.